Person: KINAY TARAN, PINAR
5 results
Search Results
Now showing 1 - 5 of 5
Publication Metadata only The Effect of Parenting Styles on Behavior Management Technique Preferences in a Turkish Population.(2018-09-15) Bakkal, MELTEM; Kaya, MUSTAFA SARP; Taran, PINAR; Özalp, ŞERİFE; KINAY TARAN, PINAR; KAYA, MUSTAFA SARP; BAKKAL, MELTEM; ÖZDEMİR, ŞERİFEPublication Metadata only Effect of Different Restorative Materials on Primary Tooth Wear: A Quantitative Evaluation Using Microcomputed Tomography(2021-01-01T00:00:00Z) KINAY TARAN, PINAR; ŞAHİNBAŞ, ABDURRAHMAN; BAYRAKTAR, GÖZDE ASENA; KINAY TARAN, PINAR; ŞAHİNBAŞ, ABDURRAHMAN; BAYRAKTAR, GÖZDE ASENAPurpose: The wear properties of o five materials used in the primary dentition must be compatible with primary tooth wear. The purpose of this study was to investigate the wear rate of primary teeth opposing composite resin and different prefabricated crown materials. Methods: The study specimens were divided into four groups: (1) composite resin (CR) group; (2) stainless steel group (5.5); (3) monolithic zirconia (MZ) group; and (4) fiberglass (FG) group. Ten specimens were prepared from each group, and primary canines were used as antagonist teeth. The wear test was conducted with a vertical loud of 50 N and 240,000 cycles using a chewing simulator. The volume losses of antagonist teeth and the weight losses of restorative materials were calculated with microcomputed tomography and a digital scale, respectively. The worn surfaces of restorative materials were examined via scanning electron microscopy. Results: The amount of enamel wear was highest in the MZ group (1.551 +/- 0.859 [standard deviation] mm(3)) group, followed by the FG group (1.028 +/- 0.854 mm(3)), SS group (0.480 +/- 0324 mm(3)), and CR group (0310 +/- 0341 mm(3)). The volume losses in the MZ group were significantly greater than those in the SS and CR groups (P<0.05). The weight loss amount of restorative materials was highest in the CR group (81.2 mg), followed by the FG (6 +/- 3 mg), SS (4 +/- 3 mg), and MZ (2 +/- 1 mg) groups. Conclusions: Prefabricated monolithic zirconia crowns caused greater wear on opposing primary teeth. The amount of weight loss in the composite resins was highest while causing minor primary tooth wear.Publication Metadata only A Comparison of Periodontal Health in Primary Molars Restored with Prefabricated Stainless Steel and Zirconia Crowns.(2018-10-01T00:00:00Z) KINAY TARAN, PINAR; KAYA, MUSTAFA SARP; KINAY TARAN, PINAR; KAYA, MUSTAFA SARPPublication Metadata only Temporomandibular dysfunction assessment in children treated with the Hall Technique: A pilot study.(2020-01-28T00:00:00Z) Bakkal, M; Kaya, Mustafa Sarp; Kınay, Taran; KAYA, MUSTAFA SARP; KINAY TARAN, PINAR; BAKKAL, MELTEMPublication Metadata only Hall teknik uygulamasında paslanmaz çelik kuronların neden olduğu oklüzal dikey boyut artışının takibi: Pilot çalışma(2018-06-01T00:00:00Z) KAYA, MUSTAFA SARP; KINAY TARAN, PINAR; BAKKAL, MELTEM; KAYA, MUSTAFA SARP; KINAY TARAN, PINAR; BAKKAL, MELTEM