Person: ZENGİN KURT, BELMA
2 results
Search Results
Now showing 1 - 2 of 2
Publication Open Access Structural and mechanical analysis of three orthodontic adhesive composites cured with different light units(2020-04-01T00:00:00Z) YILMAZ, BERZA; BAKKAL, MELTEM; Kurt, BELMA; YILMAZ, BERZA; BAKKAL, MELTEM; ZENGİN KURT, BELMAObjective: To evaluate the effects of three different curing units on the physical and mechanical features of three different orthodontic adhesive resin materials. Material and Methods: 45 specimens (5 mm in diameter, and 2 mm in thickness) of each of the three different adhesive composite resin materials (Transbond XT, Grēngloo™ Adhesive and Light Bond Paste) were cured with three different light units (a polywave third generation (Valo), a monowave (DemiUltra), and a second-generation LED (Optima 10)). To quantify degree of conversion (DC), the Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy was used in transmission mode (ALPHA FT-IR Spectrometer, Bruker Optics, Germany). Vickers hardness value was recorded under constant load 100 g for 10 s with a microhardness tester (HMV M-1, Shimadzu Corp., Kyoto, Japan). The data were statistically analyzed using Kruskal-Wallis and chi-square tests. The level of significance was considered p<0.05. Results: The highest DC values were obtained as a result of curing with Optima 10. This rate was followed by Demi Ultra and Valo, respectively. Transbond XT samples showed a lower level of conversion than the samples of Light Bond Paste and Grēngloo™ Adhesive. The top surfaces of each material showed higher hardness values than the bottom surfaces (p<0.05). The Light Bond Paste showed the highest hardness values both on the top and bottom surfaces among the three materials, followed by Grēngloo™ Adhesive. While the hardness values of the top surfaces of the samples cured with Demi Ultra and Valo light units were similar, higher hardness values are recorded with Valo on the bottom surfaces (Valo; 85.200/75.200 (top/bottom) versus Demi Ultra; 86.100/66.000 (top/bottom)). Conclusions: The different DC and the surface hardness properties were recorded for the resin as orthodontic adhesives depending on different light units. Shorter radiation time caused lower DC and surface hardness values.Publication Open Access Anticholinesterase, antioxidant, antiaflatoxigenic activities of ten edible wild plants from Ordu area, Turkey(2018-06-01) Kurt, BELMA; GAZİOĞLU, IŞIL; SEVGİ, ECE; Sönmez, Fatih; ZENGİN KURT, BELMA; GAZİOĞLU, IŞIL; SEVGİ, ECETurkey has highly rich floras of medicinal and aromatic plants because of having various climate conditions in different regions. One of these regions is Middle Black Sea Region, especially Ordu Province. Extracts of 10 edible plants (Arum maculatum L., Hypericum orientale L., Ornithogalum sigmoideum Freyn et Sint., Silene vulgaris Garcke var. macrocarpa, Plantago lanceolata L., Achillea millefolium L. subsp. pannonica, Rumex crispus L., Rumex acetosella L., Capsella bursa-pastoris L., Coronopus squamatus Asch.), grown in Ordu, Turkey, were prepared with different solvents (hexane, ethanol and water, separately) and their anticholinestrase and antiaflatoxigenic activities were evaluated. Additionally, the cupric reducing antioxidant capacities (CUPRAC) and ABTS cation radical scavenging abilities of the extracts were assayed. The ethanol extract of R. acetosella exhibited the highest antioxidant activity (A0.5 value of 25.31 µg/mL, for CUPRAC activity; IC50 value of 23.73 µg/mL, for ABTS activity). The hexane extract of C. bursa-pastoris showed the strongest inhibition against AChE enzyme with IC50 value of 7.24 µg/mL, and the hexane extract of A. millefolium subsp. pannonica had the highest BChE activity with IC50 value of 6.40 µg/mL. The ethanol extract of P. lanceolata exhibited the strongest inhibition against aflatoxin with 88% inhibition.